All Courses

Maintenance
maintenance
Operations
operational software
Application
application

How to Clean a Printhead

Don't mess up your printhead - watch this video!

2 steps

Daily Start-up Procedure

Everyone in your shop should follow this procedure for start-up

1 steps

Moving Equipment Procedure

Before moving your equipment make sure you watch this video on what you need to do so you don't damage your printer.

1 steps

Replacing Main Board

Replacing your Main Board on your 5 head DTF printer

Safety Notice: For your safety, do not attempt to service or work on the printer while it is plugged in. Always disconnect the power source before performing any maintenance to avoid the risk of electric shock or injury.

maintenance

1 steps

Cap Head Replacement

Step-by-step procedure in cap head / pad replacement

maintenance

1 steps

Flushing Ink system

Flushing the ink system the way DTF Tech Gurus suggests it will be a much more manageable procedure. If switching out inks - this is the procedure you should follow.

1 steps

Position Heads and Sensors

Overview on the version 1 3 head printer, showing you the sensor, positioning of the heads and components.

1 steps

Adjusting Belt Tension

Adjusting the belt tension on your x axis of your DTF printer

1 steps

Dryer Overview - X5 / 5 Printhead System

Quick overview of the features and some maintenance on the larger dryer for the 5 head DTF print systems

1 steps

Print Manager Overview - part 1

Print Manager overview for the 5 head printer - X5

1 steps

Wasatch Rip Software Overview -part 2

Part 2 of the Rip Software overview.

operational software

1 steps

Wasatch Rip Software Overview - Part 3 updating subscription

This video discusses updating your Wasatch Rip Software, best practices and why you want to update your subscription.

1 steps

Replacing Powder Auger Motor - X5 / 5 Printhead System

Powder Auger Overview, and in particular how to replace the powder auger motor on the 5 printhead dryer.

1 steps

Replacing Dryer Board X5 - 5 Printhead System

X5 Dryer or the dryer built for a 5 printhead printer. Before taking it a part, make sure you take a picture of the wiring, and label all the wires before disassembling the board.

1 steps

Printer lower control panel (analog) V1

Quick overview of the analog panel on the older version 1 of the Binterjet / Velox

1 steps

On-Site Tools for Self-Service

Tools you will need to work on your DTF System. We can not help you work on the machine if you don't have the right tools!

1 steps

Switching Inks? Read this before you do.

If you decide you want to switch ink sets, make sure you read this article before doing so. Not all inks work well together and you could major issues if you just pour new ink into your printer.

5 minutes

1 steps

Film comparison - Cold, Warm, Hot, Instant

Comparing Cold, Warm, Hot, Instant, Rapid....you name it ________ peel!

1 steps

Do your transfers feel like stiff plastic

Get the most out of your DTF printer - Tips on settings & supplies

application

1 steps

Cap Station Maintenance

Discussion on the components in your cap station, how things work, and some maintenance tips

1 steps

Damper Replacement

This is not a difficult task, but if done incorrectly you can end up with quite a mess on your hands.

1 steps

Low Ink Alarm & Importance of Proper Ink Levels

Make sure you are watching your ink levels!

1 steps

Powder Shaker Motor Replacement

Step-by-step procedure on replacing the powder shaker motor

1 steps

Powder Auger Motor Replacement

Step-by-step procedure on replacing the powder auger motor

1 steps

Cleaning Filtration System and Maintenance

It is important to maintain your filtration system - keep your air quality good in your shop!

1 steps

Micro Stepper Driver Replacement

The Micro stepper the logic control for the film feed. The brain of the printer, telling the motor how far to step the film. Make sure when replacing that you get the correct unit for replacement.

1 steps

Wasatch Rip Software - part 1

Great start to a 3 part video on Wasatch Rip Software

1 steps

Cleaning the White Ink Tank

This video shows you the importance of cleaning your ink tanks

1 steps

Cap Station Tray Cleaning

Keeping your cap station clean is extremely important step in maintenance of your DTF printer

1 steps

White Manifold Replacement / Cleaning

Discussion of the manifold replacement and the cleaning of the white ink line.

1 steps

Lower Heat Vacuum Control Panel - 5 printhead unit

Quick overview of the control panel on the dryer for 5 head printer

1 steps

Power Supply Replacement on dryer for the 5 printhead printer

Step-by-step procedure on replacing the power supply on 5 head printer

1 steps

Printhead registration on 5 head printer

Overview of setting registration on the 5 head DTF printer

1 steps

Print Manager Overview - part 2

Second part of the print manager overview

1 steps

Print Manager Overview - part 3

Review of the print manager - watch all three parts!

1 steps

Rear Electrical Cabinet Component - 5 head

Video on the importance of keeping the electrical cabinet in the back of the printer clean. Quick overview of components

1 steps

Suction Roller Motor - on dryer X5 - 5 head printer

Step-by-step of replacing your suction roller motor

1 steps

Replacing X motor on DTF printer

This is the motor that moves your head carriage back and forth.

1 steps

Cap Station Lifting Mechanism Removal

Step-by-step procedure on removing the lifting mechanism

1 steps

Cap Station Removal

Step-by-step procedure on removing the cap station

1 steps

Installation of Circulation Pump

Step-by-step procedure - installing your new circulation pump.

Copyright Notice: This video is the property of DTF Tech Gurus and is protected by copyright law. Unauthorized sharing, posting, or distribution of this video on any website or platform other than DTFTechGurus.com is strictly prohibited. Violators may be subject to legal action.

maintenance

1 steps

Head Carriage Bearing Lubrication

Extremely important and easy to do - lubrication of head carriage bearings

1 steps

Disconnecting Tubing from Cap Station

Quick video on best practices of disconnecting tubing from your printer

1 steps

Dryer Bulb Replacement - X5 for the 5 head system dryer

This video goes through bulb replacement on the 5 printhead system that has a more robust dryer. In this video Scott will cover some things to look for in making sure your dryer is operating correctly.

1 steps

Overview of Printheads in Version 1 printer

Discussion of the printhead layout in the 3 print head DTF printer, version 1

1 steps

Tip on Film Buckling

Check out this video on how film buckling often happens and how to keep it from happening.

0 steps

Changing Roll of Film / Tension

Easy - sure, but watch this video so everyone in your shop does it the same way - each and every time

1 steps

Cleaning Ink Tanks

Very easy-to-do, and yet so many shops neglect doing this. Please watch the video.

1 steps

Film Tension & Traction

Scott Hopper, DTF Tech Guru goes through the film tension and traction to make sure you set up the film correctly on your printer. Everyone in your shop should do the same procedure to ensure the same output.

1 steps